Mobile Welding Repair
- Cracks, broken brackets, worn mounts
- Mild steel, stainless & aluminum
- MIG, TIG or Stick — whatever the job needs
- Generator-powered rig, no hookup required
Straightforward starting prices for on-site welding and equipment repair across the Louisville area. Your free on-site estimate turns these into an exact number before any work begins.
Rates reflect current Louisville-area mobile welding pricing for a fully equipped rig and an experienced welder on site.
Our everyday service for anything metal that's cracked, snapped, worn or loose. We set up at your location, prep the joint properly by grinding to clean metal and beveling where needed, and weld it back stronger than before. Most small repairs are finished inside the first hour.
Trailers and gates take a beating, and they always seem to fail when you need them most. We repair and reinforce the weak points so the same failure doesn't come back. Typical hinge repairs and rebuilds fall in this range. Larger rebuilds are quoted on site.
Downtime costs money. We repair commercial and industrial equipment where it sits, whether that's a job site, farm or plant floor. We gouge out cracks, rebuild worn areas and add plate reinforcement so it holds up under load.
For work where strength and documentation matter. We weld to the engineer's drawings and the applicable code, and we coordinate with your general contractor and inspector so the job passes the first time.
When a gate fails with livestock behind it, or a broken trailer strands a load, waiting until Monday isn't an option. After-hours calls (weekday evenings after 6 PM, Sundays and holidays) are billed at one and a half times the standard rate for the service. You still approve the price before work starts.
Need a welder today?Brackets, mounts, racks, gates, railings and one-off parts built to fit. We measure on site and fabricate to your needs. Custom work is quoted in writing with a materials deposit. See our Refund Policy.
| Process | Best for | Materials | Why it matters to you |
|---|---|---|---|
| MIG (GMAW) | Trailers, gates, frames, general repair | Mild steel, some stainless & aluminum | Fast and clean, so less billable time on routine jobs |
| TIG (GTAW) | Thin, visible and specialty work | Aluminum, stainless, thin-wall tube | Precise heat control, so no burn-through and a clean finish |
| Stick (SMAW) | Heavy equipment, structural, outdoor | Carbon steel, cast iron (repair), heavy plate | Handles wind, rust and thick sections: the strongest field repair |
Material type and thickness, access to the repair, how much prep the joint needs, travel time to outlying areas, and whether new steel is required.
New steel, hardware and consumables beyond normal use are itemized on your estimate, so you see exactly what you're paying for.
Cards, cash, and checks for approved commercial accounts. Due on completion unless your estimate states a deposit.
Yes, that's exactly how we operate. RigReady runs a fully equipped, generator-powered welding rig, so we can work in your driveway, barn, job site, parking lot or loading dock without needing your power. If something truly can't be repaired on site, we'll tell you upfront.
Yes. The on-site estimate is always free. We look at the damage, explain what failed and how we'll fix it, and give you a price. Nothing starts until you approve it.
General mobile welding repair is billed at $95–$125 per hour with a 1-hour minimum. Many small repairs (a broken hinge, a cracked bracket) are finished within that first hour.
After-hours emergency calls (evenings, Sundays and holidays) are billed at 1.5× the standard rate. You'll still get a price to approve before we start.
MIG for fast, clean work on steel; TIG for precise work on stainless, aluminum and thin material; and Stick for heavy, dirty or outdoor repairs on structural steel and equipment. We pick the process that gives you the strongest, longest-lasting repair.
Yes. Aluminum trailers, ramps, boat parts and stainless fixtures are all regular jobs. Cast iron can often be repaired too, but we'll explain the limits before we start.
Yes. Every job comes with our 30-Day Workmanship Guarantee. If a repair fails because of our workmanship, we'll re-inspect and correct it at no additional labor cost. See our Refund Policy and Terms for details.
We accept major credit and debit cards, checks for approved commercial accounts, and cash. Payment is due when the job is complete unless your written estimate says otherwise. Larger jobs that need materials ordered may require a deposit.
Make sure we can get the rig reasonably close to the work, clear flammable materials from the area if you can, and let us know about anything we should watch out for (fuel lines, livestock, buried utilities, hydraulic pressure). We handle the rest.
Book your free on-site estimate. No obligation, no pressure.